In the direct cost of pig production, feed accounts for about 70%. In the situation where feed prices continue to climb, it becomes increasingly important to be able to meet the nutritional requirements of the organism while saving feed and increasing income. Here are a few simple ways to increase the size of your pigs:

Choosing the right piglet size pigs must choose to raise “three yuan” crossbred piglets. The best is to use Changbai and Yorkshire pigs with long waist, wide chest, short mouth, full hips, thick limbs, and food for grab food. It takes about 160 days to reach 90 to 100 kg, shortening the fattening period by 20 to 50 days.

The pigs reared in separate circles should be kept in separate circles after 60 days of age, with 2 to 3 pigs per lap, so as to avoid chasing and running energy in the outdoors.

Castrated 30-day-old boars and 40-day-old gilts were castrated in a timely manner. They were 15% heavier than the customary 60-day-old grazing, and the wounds healed quickly, shortening the fattening period by about 20 days, and saving feed by 20%. about.

Timely deworming stomach piglets drive the first insects at 60 days of age, and then once every 2 to 3 months to repel insects, according to pigs per kilogram of body weight with anti-creeping or insect repellent net 15 to 20 mg, a feeding seasoning, Repel internal parasites. If there is swine fever, 10 g of salt, 10 ml of kerosene, and 20 ml of warm water can be mixed and applied to the surface of the pig to kill insects. At the same time as deworming, 1 kg of quicklime was dissolved in 5 kg of water for each pig. The above supernatant was fed and fed twice a day. Two to three days of gastric lavage was used to remove various insect pests. One week later, pigs were given a piece of rhubarb soda per kilogram of body weight (maximum no more than 15 tablets), and the stomach was fed in three batches. In this way, each pig can increase the weight of 10 to 15 kilograms and shorten the 25 to 40 days of fattening period.

Scientific feeding is based on the growth and development laws of the pigs that grow slowly in the early stage, fast in the middle stage, and slow in the later stage. In order to obtain higher feed remuneration, linear breeding methods should be adopted to shorten the feeding period and save the feed. At the same time, it is necessary to implement fine, green, and coarse feed mixes, and to implement dry feed for raw feeding; in the number of feeds, two feeds should be taken daily to reduce the consumption of energy and feed due to multiple feedings to stimulate pig movements. Loss of throwing, reducing feed utilization.

The empty breeding phase of sows and the first 80 days of pregnancy can be based on green fodder, high-quality roughage, and bad-slag feeds. Only about 1 kg of concentrate is used each day. One month before labor, feed 2 to 3 kg of concentrate every day. In this way, the normal development of the fetus is guaranteed, and the sow can save 60-90 kg of concentrate feed for each pregnancy.

The timely mating of the piglets at 60 days of weaning is advanced to 40 to 45 days, which can promote the early estrus and early mating of the sows, shorten the period of idleness, and relatively save the feed.

Strictly prevent the epidemic disease In spring and autumn each year, timely injection of "triple seedlings" to pigs can effectively control the three major diseases of swine fever, swine erysipelas and swine plague, reduce the mortality rate and relatively reduce the consumption of materials.

When the weight of the hog weight is 20 to 90 kg, the daily weight gain rises linearly. After 100 kg, the growth rate is slow, and the daily weight gain gradually decreases. Therefore, the slaughter of the hog when raising about 90 kg is good.

KEY CUTTERS FOR JMA MACHINE AFTERMARKET

JMA KEY CUTTERS

1 Material: It is made of high grade wear resistance and anti-breaking carbide material, Co%>10%. ultrafine grain, high cobalt content, good wear resistance and not easily broken

2 Manufacturing process: Be produced by 5-axis grinding center. High gloss grinding, sharp edge, can cut copper key, nickel silver key, including Honda, Volkswagen original key and STRATTEC keys.

3 Features: 4 cutting edges, Stronger teeth design to prevent broken, good impact resistance, effectively overcome the problem of broken cutter; suitable for the processing of C-class key cylinder mult

Suit for Machine: various vertical manual key machines, 363, 333L, 339, 369, 368A&B, 398AC, 399AC, 369,368B,383AC,388AC,398AC,399AC, Q36,Q38,Q39,Q30,Q32,Q31

Suit for processing keys:

1 especially suitable for processing C-class lock cylinder multi-track keys, all internal milling slots and external milling slot keys

2 suitable to cut copper key, white copper key, nickel silver key, including Honda, Volkswagen original key and STRATTEC keys.

Key Cutters For Jma Machine,Jma Milling Cutter Wheel,Jma Angle Tracer Point,Key Cut Wheel For Jma

ZHANGJIAGANG KEYCUT CO.,LTD , https://www.keycutblade.com